The Feather² was designed with simplicity in mind, using under chambered airfoil section, super thin trailing edge reversed d-box design to make the model more sensitive to weak thermals . Using 10 airfoil ribs along each wing panel, with the last two foils slightly modified for a slight wing twist change (washout) allowing for better lateral airflow, this improves energy retention and over all provides a floaty aircraft, putting a whole new meaning to “rising to the occasion”. Practically unbreakable, the Feather’s ultralight signature weight and carbon fiber reinforcements allows for even the hardest crash landings without a single scratch or dent.

The Feather² Squared glider comes with laser cut ribs, laser

cut tail feathers ( rudder & elevator ), laser cut control horns and launch peg housing. Main boom is carbon fiber, with carbon fiber pushrods, carbon fiber leading edge  and carbon fiber main wing spars. Both tail feathers have  pre-cut control horn slots and hinge line.

No other radio control glider this size and scale will perform like the Feather² Squared. At a tender weight of 43-47 grams, attractive design with built-up wing ribs, catching thermals at your local park has never been easier. Flying the Feather² glider can be a very peaceful and relaxing experience. Gliding at slow speeds gives stability and plenty of time to react.

To cover the balsa ribbed wings on the Feather² Glider, light weight colored tissue paper is used. Included in the kit you will find 4 white pieces to cover both wing panels and random trim colors for counter balance and esthetics. These are .8 grams per sheet ( 4x = 3.2grams ). Your other options are Esaki Japanese Tissue or Gampi Japanese Tissue, these are .6 grams per sheet ( 4x = 2.4grams).

Specifications:

Wing-span :	28.5″ (736mm)
Wing-area :	113 sq/in.
Wing-loading :	1.89 oz./sq.ft
Weight :	43-47 grams+-
Control :	2ch rudder/elevator
Manufacturer :	MicroBirds
Fuselage :	Carbon Tube
Wings :	Balsa Wood
Version :	Kit
Battery :	150mAh 1s
Receiver :	2-4ch micro
Assembly :	Easy
Skill Level :	Everyone/DLG +
Wind Cond :	0-10mph

Kit Contents: Laser cut balsa airfoil ribs | Laser cut tail feathers | Laser cut control horns | Laser cut launch peg housing | 2x thin balsa sheets | Balsa secondary d-box spar | 2x Carbon leading edge rods | 2x Carbon fiber wing spars | 2x Carbon fiber push rods | 3x Carbon fiber tow strands | XPS foam pod/carbon tissue | Glass Fiber sheets | Carbon boom fuselage | Various | small parts for linkage | 4x Shrink tubes | 3x battery and servo plugs | Micro Tip CA glue nozzle tip | 4x white tissue for covering | Glue stick | 1x Mini brush | Step by step video build guide | Blueprint layout plan

Electronics: For optimal performance, 1.7 gram micro servos should be used coupled with 1.5 to 2 gram micro receiver, making sure receiver and servo connection are micro JST 1.25mm socket. If using Spektrum DSM radio system and JR, proper electronics are listed below. For all other radio systems, contact me for more information.

Tools to finish glider:

The Feather² Squared come with a step by step HD video build guide, providing simple and easy way to learn and follow directions, building your glider from start to finish. 1. Medium CA glue ( thin CA glue optional but helpful ) 2. gorilla glue ( expandable) 3. painters tape 4. sand paper ( 100 medium to 300 ) 5. scissors 6. Xacto blade 7. 30min or 24hr epoxy 8. scotch tape 9. needle nose pliers 10. Ruler 11. One free afternoon 🙂

Required to complete:

2x Micro 1.7 gram servos Click here for more info
Micro receiver  2.4GHz 4 Channel DSMX DSM2 for Spektrum and JR transmitters  Click here for more info
150mAh 1s lipo battery Click here for more info
Solar-Film Ultralight Lamination Film. Click here for more info